I purchased one tin of patio sealer to try on the front patio. The results were so good that I had to purchase a further two tins to treat the main patio at the rear of the property. As I had some sealer left over - I then treated my mother-in-law's patio. I lost a weekend - but gained a few "brownie points"!
Micheal Hatcher, from Canterbury
Overview
SmartSeal Patio Sealer has been developed to combat the constant problems of staining and weed growth and to enhance the colour and aesthetic appeal of new or mature patio slab. This sealed surface will increase abrasion resistance and also protect the pointing from erosion and weed infestation and provide a barrier to contaminants thereby facilitating easy maintenance. (**Due to its porosity NOT recommended for use on Natural Stone or Sandstone )
- Enhances natural colours of Pre-Cast Patio & Sandstone slabs
- Brings old patios alive
- Easy to apply Patio sealer with sprayer, roller or brush
- Protects against loss of colour through UV light
- Resists oil and stain penetration
- Inhibits weed and algae growth
- BS5750/ISO9000 quality approved Patio Sealer
- For optimum results apply two coats
- Suitable for most patio slabs
- Average coverage 4-6 sq metres per litre
Recommended coverage
First coat: approx 4sq metres per litre
Second coat: approx 5sq metres per litre
Technical Information
Application
Smartseal Patio sealer can be applied using a sprayer unit or roller, at a rate of 4 m2 per litre (pavers) 1st coat & 5 m2 per litre 2nd coat. A two-coat spray application is required to fully cover the jointing sand. The sealer will be tack free within 2 hours at 20°C and foot traffic may be permitted after 4 hours. These times may be increased or reduced depending on the ambient temperature. During the curing cycle, protect from rain. Do not apply when the ground temperature is above 30°C or below 5°C. All equipment should be cleaned with Smartseal Xylene cleaner after use.
Deicing salts should not be applied directly on Smartseal block paving, patio or concrete sealers. Salt chemically reduces the temperature at which water freezes and will result in water ingress into the concrete. Subsequent freezing may result in the concrete ‘seal’ being broken by the expansion of water as it freezes and white ‘pitted’ areas may become visible.
Preperation
New Patios should be swept clean, ensuring there is sufficient pointing in the joints. Existing paving should be pressure washed to remove all surface debris. If the area is contaminated with weeds & moss then it should be treated with Smartseal Fungicidal Wash. Oil and other stains should be removed using Smartseal Cleaner / Oil Remover. The treated area should then be left to dry and the joints re-sanded & compacted to the lower edge of the paver chamfers with clean kiln-dried sand. Moisture in the paver & sand will inhibit penetration of the sealer and produce whiteness.
Technical & Test Data
Smartseal Patio sealer has been tested by the TRL (Transport Research Laboratory) and certified that it meets the SRV (Skid Resistance Value) for all categories of paving for local authority pedestrian areas and when heavily trafficked is suitable for special applications where risks of skidding are high as laid down in the UK Highway Authorities Tender Specification. Copies available on request.
Specification Clause
“Newly laid Patio paving shall be treated with Smartseal Patio sealer to protect and stabilise the paving and pointing. application will enhance surface colour and increase abrasion resistance. All materials should comply with ISO9002 for Quality Assurance. All work should be carried out in conjunction with the manufacturer’s current technical data sheet and instructions for use”.
Health & Safety
Flammable liquid. Do not smoke. Keep application area well ventilated. Wear respirator when applying. Store in a cool place. Flash point 40°C (Abel-Closed Cup). Refer to the Health & Safety Data Sheet for further information.
Patio Sealer Application Guide
Home Owners & DIY 
Trade Customers 
Contractor Login 