'BLOCK MAGIC' Sealer TAN (sample 5 & 25 L) Re-colour Old Block Paving - ALWAYS- Apply 2nd coat of CLEAR Sealer

Customer Reviews

Very good service from ordering and and delivering . And before I order I did fill out the online form to find out which is right product the block paving . I got call back from lovely customer service. . I havent used the product yet so cant say much . Very Small Tin so not sure how many pacing I can I try it on .so fat everything went well . Thanks

By Hemali Tailor

Fantastic product

By Valerie Webster

Fantastic product

By Valerie Webster

Ask Us A Question

Description

Step-by-Step Video Guide

Add colour to your block paving to make it look like new.

Smartseal "Block Magic" is a blend of liquid pigments and acrylic resins that soaks deeply into paving, totally transforming and protecting block paving driveways and patios. 'Block Magic' replaces the colour that sun, rain, vehicles and pressure washing has taken away. Apply one coat of 'Block Magic' by brush or roller, leave to dry, re-sand the joints and then apply a coat of our clear sealer.

***NOT TO BE USED ON CLAY PAVERS

Transforms Old Block Paving

Recolours and Protects
UV Stable
Colour Fast
Stain Resistant
Hard Wearing
Covers 3 m²/litre on average based on one coat
Other Colours Available

See Technical section below for more information.

Technical

Liquid UV stable pigments blended with acrylic resins and solvents create "block magic". Developed by Smartseal with older block paving in mind, it will not only recolour block paving but protect the paving from future colour loss, weeds algae and staining.

'Block Magic' Coloured Paving Sealer is applied by roller, at a rate of approx 3.0m² per litre. Make sure the colour has dried evenly across the block paving before applying a clear second coat of sealer.Prior to applying sealer, sweep kiln dried sand into the joints and ideally compact with 'wacker plate'.The sealer will be tack free within 2 hours at 20°C and foot traffic may be permitted after 4 hours. Vehicles should be kept off the sealed area for a minimum of 24 hours at 20°C. These times may be increased or reduced depending on the ambient temperature.
Ensure no rain is forecast for at least 6 hours after application. Do not apply when the ground temperature is above 25°C or below 12°C.
All equipment should be cleaned with Smartseal cleaning fluid after use.

Deicing salts should not be applied directly on sealed block paving or concrete sealers.
Salt chemically reduces the temperature at which water freezes and will result in water ingress into the pavers.
Subsequent freezing may result in the paving 'sealer' being broken by the expansion of water as it freezes and white 'pitted' areas may become visible.

*****NOT TO BE USED ON CLAY PAVERS

*** If your Block Paving has been previously sealed - to ensure compatibility, please contact us here before ordering: https://www.smartseal.co.uk/help-advice/contact-us.htm

Preparation

Existing paving should be pressure washed to remove all surface debris and muck from the joints.
If the area is contaminated with weeds & moss then it should be treated with Smartseal moss clear or weed killer.
Oil and other stains should be removed using Smartseal Driveway Cleaner or Oil Remover.
The treated area should then be left to dry and the joints re-sanded & compacted to the lower edge of the paver chamfers with clean kiln-dried sand.
Moisture in the paver & sand will inhibit penetration of the sealer and produce whiteness.

Technical & Test Data
Smartseal Block Paving sealer has been tested by the TRL (Transport Research Laboratory) and certified that it meets the SRV (Skid Resistance Value) for all categories of paving for local authority pedestrian areas and when heavily trafficked is suitable for special applications where risks of skidding are high as laid down in the UK Highway Authorities Tender Specification. Copies available on request.

Specification Clause
"Newly laid block paving shall be treated with Smartseal block paving sealer to protect and stabilise jointing sand and enhance surface colour and increase abrasion resistance.
All materials should comply with ISO 9002 for Quality Assurance.

All work should be carried out in conjunction with the manufacturer's current technical data sheet and instructions for use".

Health & Safety
Flammable liquid. Do not smoke. Keep application area well ventilated.

Wear respirator, gloves and goggles when applying. Store in a cool place. Flash point 40°C (Abel-Closed Cup). Refer to the Health & Safety Data Sheet for further information.