Solvent Free Block Paving Sealer (Eco Friendly) - Available in 5 & 25 Litre containers - No Smell or Fumes.
12 Reviews|(5/5)
Customer Reviews
Easy to apply using a squeegee. Odour-free. Good coverage and absorption into block joints. Very pleased with the result. Brilliant order processing and delivery by Smartseal.
Seems to be an excellent product, will be interesting to compare with the sovent-based sealer over time.
New drive, new product, well new to us. Goes a long way, solvent free so no fumes when applying.25 lts plenty for our 50 or so sq metres. only drawback some places showing white on bricks after rain but dries out o.k all in all will use it next time we have to seal. Looking forward to seeing long time results, at moment rain running off and doing what it says on container.
Very happy with the result.
absolutely fantastic, my customer was extremely happy with the results, Will not use anything else AAA+++
Easy to apply, prompt delivery, happy so far, but too soon to determine long term performance.
I last used this sealant four years ago & have never refreshed it or washed the driveway down. In all honesty, I also economised a bit on sealer since the driveway is quite a big area & I should ideally have used 6 drums but just managed with four, so this year the driveway was looking a bit grubby & moss appearing in joints. I spent a few days raking out all the poor joints , applied moss killer and resanding. I also modified a little watering can and went over all the fresh joints with sealer to make sure there was enough to soak right in. Next day I did the whole of the driveway again : three drums were more than adequate since the blocks and joints were not very porous any more and because the driveway is slightly uneven I found brushing it on with a soft window-cleaning brush worked a treat rather than using the squeegee. It's all dried now, the finish is superb, rain just beads and runs off and the sanded joints are set hard. No smell, no mess, easy to apply, a superb product.
I purchased two drums of the Eco-friendly Smartseal block drive sealant. It was easy to use and the instructions, supported by an online video, were easy to follow. Ajob well done, I think.
We always use the Solvent Free Block Paving Sealer (Eco Friendly) on our block paving. Easy to use, no smell and a fantastic finish.
So far it seems to be good, but as I told you on the phone my drive is not level and the Sealer ran down very quick in the joints. I had to order another two as I ran out very quickly. I would rate it 3. It may get better when finished.
the product was very easy to use,customer was delighted with end result
Description
Solvent-Free and Eco-Friendly Block Paving Sealer to stop weeds growing in the joints of block paving. A water-based block paving sealer and weed inhibitor with no smell or fumes due to its solvent-free formulation.
Highly effective, easy to apply sand hardener and block paving sealer, will inhibit the growth of weeds and moss and protect blocks.
APPLICATION and PREPARATION GUIDE
- Penetrates deep into sand
- One or Two coat application (see coverage)
- Sets jointing sand solid
- Restricts weed and moss growth
- Easy to apply by watering can and squegee
- Manufactured to BS5750/ISO9001 standard
- Gives additional protection to pavers
- Stain and Oil resistant
COVERAGE
For best results to allow product to penetrate approx 20mm into joints, apply at a ratio dependent on width of joints at 1.5 m2 per litre first coat, approx 4.0 m2 second coat
APPLICATIONS
Only suitable for use on standard concrete based block pavers - Not to be applied to clay pavers.
Technical
Block Paving Sealer (eco friendly) - See 'How To' Video Guide
Preparation: New Blocks Apply as soon as possible after installation. Remove excess sand. Apply above 8°C. Do not apply to wet surfaces, or if rain is forecast within 8 hours.
Older block paving: Thoroughly clean off the blocks with power wash, stain remover and fungicidal wash as necessary. Allow blocks to completely dry before re-applying jointing sand until all joints are properly filled before application of Weed Inhibitor / Sand Hardener.
Application: By watering can or direct from container, apply liberally, working solution across surface with squeegee. Ensuring full absorption into depth of jointing sand.
Coverage: Dependent on depth of pavers 1m² / 2m² per litre. Product will appear opaque when wet, but will be clear when dry.Ensure adequate supplies of product are available. Agitate drum before opening, keep sealed when not in use. Clean spillages with water.
Health and Safety:
Harmful by inhalation and if swallowed. Irritating to skin.
Wear appropriate safety wear at all times.
***NOT TO BE USED ON CLAY PAVERS
Easy to apply , hopefully no more oil marks. Underestimated amount to buy had to re-order but 2nd coat applied without any hitches. Natural Matt finish although in certain sunlight angles of view looks a bit shiny. But not enough to look bad. Good product will buy again