Porcelain Sealer - One Coat - Stain & Scratch Resistant
Easy application, 100% breathable. Advanced, Nano-coating sealer. Safe, low-odour formula. Coverage: 10 - 20 m²/litre
Smartseal Porcelain Sealer is a hard wearing, breathable, protective coating for modern internal & external porcelain tiles. The porcelain tile sealer can also be used on ceramic wall and floor tiles. Furthermore, it helps to prevent general soiling & surface staining. Although this is not a cosmetic product, it does act as a colour enhancer and leaves a subtle wet look sheen once dry. However, its main purpose is to make cleaning and maintenance easier.
Smartseal Porcelain Sealer is a ready to use, easy to apply, quick-drying formulation that gives additional protection oil and water-based stains whilst enhancing the natural colours of the tiles. Once applied the porcelain tiles sealer will make cleaning and maintenance of porcelain surfaces much easier. WE DO NOT RECOMMENDED USING ON HIGHLY POLISHED SURFACES.
FEATURES
- Suitable for use on porcelain and ceramic tiles
- Strictly a single-coat application
- Leaves a subtle wet look sheen once dry
- Enhances the colours of the tiling
- Can be used externally on patios
- Also for use on walls and floors internally
- Ultra-durable sealer for long term protection
Formula is ready to use, quick drying and easy to apply.
Average coverage: 10 - 20m² per litre, dependant on surface texture and porosity.
Application temperature range: 10° to 23°C
Directions for Use:
Always apply to a test area or spare tile first.
Only apply to completely dry and clean surfaces.
**If applied to a surface where a "sweep-in" pointing compound has been used within the last 6 months, the porcelain must be fully cleaned with Smartseal Residue Remover prior to sealant application.**
Apply a single thin, consistent coat, with a microfibre cloth, microfibre flat mop or paint pad. Avoid application marks and excess pooling of sealer.
Please note:
This formulation is strictly a single coat application, because it is a high active micro coating that bonds very strongly to the impervious porcelain.
It is not a cosmetic product. Although it does make the treated surfaces look more attractive, its main purpose is to aid easier cleaning and maintenance.
Applying more than one coat to achieve the "desired appearance" will almost definitely result in application issues and product failure.
Given the above, it is important the exact application instructions are followed.
- Allow a minimum of 2 hours drying time before walking on. The sealer will be fully-cured and attain full water-resistance after 24 hours.
- If using externally, do not apply if rain is forecast within 8 hours.
- Average coverage 10-20m² per litre. Coverage will vary depending on surface texture and porosity.
- Store in cool, dry conditions out of direct sunlight in original container only. USE WITHIN 6 MONTHS OF PURCHASE & WITHIN 3 MONTHS ONCE OPENED.
Q: Hi I am looking for a sealant to seal a radon water feature looks like natural stone can you recommend any of your Products suitable for this job Thank you George’s
A: If the water feature is made of natural stone, then any of the natural stone sealers on our website should be suitable. If it is primarily just to seal the water feature and not change its appearance, I would suggest the DRY finish natural stone sealer may be the most suitable.
Q: Hi, We have sanded joints between some porcelain and concrete tiles, I was hoping to use this to seal both together including the joints. But I am worried about a paint pad collecting and spreading the sand creating an awful permanent mess. Can I apply this product with a garden pressure sprayer so the sand doesn't get disturbed? If no, how permanent is the solution while wet (ie if sand gets mixed in could I quickly jet-wash the whole thing away before it drys)? Finally, if the seconds answer is also no is there a different more suitable protection/sealing product I should be using? Many Thanks.
A: We do not recommend using a pressure sprayer to apply the porcelain sealer. Always apply to a test area or spare tile first and only apply to completely dry and clean surfaces. **If applied to a surface where a "sweep-in" pointing compound has been used within the last 6 months, the porcelain must be fully cleaned with Residue Remover prior to application.** Apply a single thin, consistent coat, with a microfibre cloth, microfibre flat mop or paint pad. Avoid application marks and excess pooling of sealer.
Q: Can You use this outdoors .
A: The porcelain sealer can be used indoors or outdorrs on porcelain paving.
We provide a national delivery service for our block paving sealer, pattern imprinted concrete sealer, roof coatings and tarmac restorer on a standard 2 - 4 working day basis. Dependent on weight, this is normally done by pallet or parcel carrier.
If you need products delivered quicker, for a small additional charge, orders placed before 1.30pm can be delivered within 1 - 2 working days to most parts of the UK, although this is dependent on the courier service in your area and the product/s ordered. If you require this service, please check on area availability by calling 01268 722500.
Our commitment is to supply all orders as placed and we offer a comprehensive guarantee of quality. Providing a reliable delivery service to all our customers is most important to us and this is backed up by the many satisfied customer testimonials we have received over the years.
If you need an order delivered to a different address, left somewhere at your property without a signature or left with a neighbour, just let us know.
We also try to maintain 100% stocking levels of our products at all times, so an immediate despatch is virtually guaranteed.
Our product returns policy can be viewed by visiting our Terms and Conditions section.
*Free delivery on orders over £75 are subject to the delivery address location.
The porcelain sealer is a great product, extremely easy to apply and dryers pretty quickly
The porcelain sealer is easy to use does what it says
Excellent product. Easy to apply and fast working. Ideal for porcelain.